GLOW PLUG (24V) {SINGLE}

SUPERSEDED

NSN

2920-01-188-3863

MORE DETAILS DOES IT FIT? TECH HELP TECH HOW TO GOVT SURPLUS FITMENT RELATED

IMPORTANT PART NOTE:

NO ADDITIONAL DETAILS AVAILABLE AT THIS TIME

ADDITIONAL PART NOTE:

SINGLE GLOWPLUG, SET OF 8 PN# 12338771-8. STAMPED WITH AM GENERAL'S PART NUMBER NOT AFTERMARKET

HPG ETM (ELECTRONIC TECH MANUAL) LOCATIONS - IF AVAILABLE. CLICK ON THE LINK TO VIEW A VISUAL LOCATION FOR THAT ITEM.


HMMWV PARTS > COMMON PARTS > ENGINE > GLOWPLUGS & CONTROLLERS
HPG ETM > HMMWV > 6.5L TURBO DIESEL > FUEL SYSTEM > 32 - GLOW PLUG

GLOWPLUG OPERATION ISSUES: If the Wait to Start Light flickers on and off when ignition switch is turned to the on position and engine is cold, this is normally an indication of a defective glow plug controller or glow plugs. If the Wait to Start Light comes on and stays on when ignition switch is turned to the on position and glow plugs do not cycle, (engine cold), this is normally an indication of a defective protective control box. If the glow plug system still continues to cycle after engine is warmed up, check for a 24-28 volt signal at alternator lead 2A. If no voltage is present or voltage is not within limits, replace the alternator. If 24-28 volts DC is present, replace protective control box.

TO TEST THE GLOW PLUG: Connect one test lead of multimeter to THE TIP OF THE GLOWPLUG and other test lead to threaded area OR ENGINE BLOCK (IF STILL INSTALLED) Glow plug internal resistance should be 1.5-2.5 ohms. If resistance is not 1.5-2.5 ohms,replace glow plug.

BELOW ARE THIS PART'S MATCHED USED ON CODES (UOC) TO DETERMINE PROPER FITMENT. THESE CODES ARE CONSTANTLY BEING UPDATED. CONTACT US IF YOU HAVE QUESTIONS.

---

NOTE: Part data was compiled by HPG. Please don't copy it for eBay listings, your website or anything else. Karma will hunt you down if you decide to copy it.

BELOW ARE THIS PART'S MATCHED USED ON CODES (UOC) TO DETERMINE PROPER FITMENT. THESE CODES ARE CONSTANTLY BEING UPDATED. CONTACT US IF YOU HAVE QUESTIONS. HOVER OVER THE MODEL TO SEE ADDITIONAL DETAILS

---

NOTE: Part data was compiled by HPG. Please don't copy it for eBay listings, your website or anything else. Karma will hunt you down if you decide to copy it.

GEP23500018 / 01-188-3863

GLOW PLUG (24V) {SINGLE}

Contact for Availability

[ITEMPRICE] [ITEMPRICE] [ITEMSALEPRICE]

View Details

---

Do I have a Hummer H1 or Surplus HMMWV(R)? Does it really matter...

Answer: YES

While some parts will fit either chassis there are certain unique parts and if you incorrectly interchange them THEY WILL NOT FIT. (pause and re-read that again)

The key difference, and it makes the whole experience better in buying and owning your vehicle, starts with the VIN or SERIAL Number. KNOW WHAT YOU OWN. You do NOT own a 1989 Hummer H1...you own a 1989 HMMWV®. You do NOT own a 2004 M1123 Hummer H1..you own a 2004 M1123. So knowing you have a surplus HMMWV® or Hummer H1 you can now properly get the correct fan clutch (because there are 4 clutch options)...get it?

Hummer H1: Vin starts with 137# (#= D, F, L, P, X, Y OR Z ) Total of 17 digits. Example 137YA8338TE123456. Vin is located on the windshield frame, frame rail and door frame. This vehicle was DOT certified/crash tested, is ONLY 12V and meant for the highway/offroad.

Surplus HMMWV(R)): Serial numbers are 6 numeric digits located on the driver door data plate, next to the body style tag MXXXX. (Example: 125611, M998). Unless you are armed forces this is a military surplus vehicle, is ONLY 24V from the factory and meant for battle.